manual shearing machine price Instructions

1. Start the shearing machine for a few cycles of idling to ensure that under normal conditions, test cuts of different thicknesses, from thin to thick. Ensure that the user is familiar with the blade performance of the hydraulic guillotine shearing manual shearing machine price.

2. Different blade gaps must be adjusted for different plate thicknesses during trial cutting. If the corresponding blade gap is not adjusted, the blade durability will be affected manual shearing machine price.

3. Turn on the pressure gauge switch during the cutting process and observe the oil pressure value. The pressure should be less than 20MPa when cutting a 12mm plate. This remote pressure regulating valve No9, the pressure is set to 20-22MPa when leaving the factory, the user must abide by this regulation, and shall not increase the pressure for cutting beyond the specified material surface and cause damage to the machine.

4. Sound balance during operation. If there is noise on the blades of hydraulic guillotine shearing, stop and check. The maximum temperature of the fuel tank is less than 60 degrees during operation, and should be shut down and rested when it exceeds.

Safe operating procedures

1. Before an operation, wear tight-fitting protective clothing, fasten the cuffs, and not open the hem of the jacket. Do not wear, take off, or wrap your clothes around the machine to prevent the machine from being twisted. Safety helmets must be worn, braids should be put into the hat, no skirts, slippers manual shearing machine price.

2. The operator of this machine tool must be familiar with the main structure, performance and use of the hydraulic guillotine shearing blade.

3. This machine tool is suitable for cutting various steel plates, copper plates, aluminum plates and non-metallic material plates whose material thickness is the rated value of the machine tool, and must be materials free of hard marks, welding slag, slag inclusions, and welds, and excessive thickness is not allowed .

4. How to use hydraulic guillotine shearing blades: A. Adjust the blade gap according to the thickness of the material being cut. B. Adjust the profiling or fixture according to the width of the material to be cut. C. Make 1-3 idle strokes before the machine is operated, and cut work can be carried out after normal.

5. If the machine is found to be operating abnormally during use, immediately cut off the power and shut down for inspection. When adjusting the machine tool, the power must also be cut off. When moving the workpiece, pay attention to the safety of your hands manual shearing machine price.

6. All parts of the machine tool should be kept lubricated frequently. The operator should fill the lubricating oil once per shift, and the mechanics should fill the rolling bearing part with lubricant once every six months.

Maintenance procedures

Only good maintenance of the shearing blade can make it have a long life and make it more comfortable for users. The shearing blade is a kind of forging machinery, and its main function is the metal processing industry. Let’s talk about the maintenance method of the shearing blade manual shearing machine price.

1. Opérez en stricte conformité avec les procédures d'exploitation.

2. Ajoutez de l'huile de graissage selon les exigences du tableau de graissage à chaque fois avant de démarrer la machine. L'huile doit être propre et exempte de précipitations.

3. The shearing blades must be kept clean frequently, and the unpainted parts must be anti-rust grease.

4. The lubricating oil in the motor bearing should be replaced and refilled regularly, and the electrical part should be regularly checked for normal and safe operation.

5. Regularly check whether the triangle belt, handle, knob and button of the shearing machine blade are damaged manual shearing machine price.

Replace in time and report to spare parts for supplement.

6. Regularly check and repair switches, insurances, and handles to ensure reliable operation.

7. Lubricate and scrub the machine tool 10 minutes before get off work every day.

8. It is strictly forbidden for non-designated personnel to operate the equipment, and it must be stopped by people off the machine sheet metal shearing machine price.

9. Reasonably choose the shearing gap according to the thickness of the board.

10. The board should not be stained with impurities and hard objects.

11. Avoid cutting and welding old boards.

12. Avoid excessive shearing of thick plates and adjust the gap between the upper and lower blades regularly.